Cockpit SRS Incl. Sensor Switch & Patch Leads

PowerBox-Systems Cockpit SRS w/Sensor Switch & Patch Leads
PowerBox-Systems Cockpit SRS w/Sensor Switch & Patch Leads

enlarge-icon  Click On Images to Enlarge

Overview

PowerBus Icon PowerBus Icon PowerBus Icon

Features

  • SRS: Serial Receiver System provides the facility to use receivers with serial interface: Spektrum DSM2 and DSMX (incl. X-Plus channels), Multiplex M-Link, Futaba S-Bus, HoTT, JR X-BUS and Jeti R-SAT2
  • Servo-Match function: servo centre, end-points and reverse for 4 channels and 8 servos
  • Door sequencer: six freely programmable outputs with set-up assistant
  • Unrestricted channel assignment for all PowerBox outputs
  • Graphic OLED screen with 128 x 64 pixels
  • Extremely user-friendly menu-based programming using the SensorSwitch
  • 11+1 channels
  • Signal amplification and interference suppression for all 21 outputs
  • Flight recorder, recording of lost frames, fail-safe events and all battery data
  • Variable frame rate, range 9ms - 21ms
  • 16-bit processor for fast, high-resolution signal processing
  • double-regulated output voltages for receivers and servos
  • regulated voltage with selection facility, 5.9V or 7.4V
  • Connection facilities for Futaba*, Jeti, Spektrum, HoTT and Multiplex MSB downlink bus systems
  • Direct transmission of battery voltage and capacity to the transmitter
  • Separate voltage and capacity display for each battery
    Minimum value memory alerts the user to voltage collapses
  • Large-area heat-sinks for high regulator performance
  • Regulator monitoring, regulator error indicator
  • Support for three battery types: LiPo, NiMH / NiCd, LiFePo
  • Suppression of any servo feedback currents which may occur
  • Updateable with PowerBox Systems USB Interface connectors

Technical Data

Operating voltage4.0V - 9.0V
Power supply2S LiPo, 2S LiIon, 2S LiFePo, 5S NiCd/NiMH
Current drain Power-on state130mA
Current drain Standby15µA
Maximum load currentPeak 2x20A
Drop-out voltage0.3V
Output voltage5.9V or 7.4V regulated
Signal inputserial
Supported RC systemsSpektrum, Futaba, HoTT, M-Link, Jeti, JR
Receiver redundancySRS
Channels11+1
Servo sockets21
Programmable servo outputs4 channels, 8 servos
Servo signal resolution0.5µs
Signal frame rate9ms, 12ms, 15ms, 18ms, 21ms
ScreenOLED 128 x 64 pixels, graphic
Integral door sequenceryes
Supported telemetry systemsFutaba*, Jeti, Spektrum, HoTT, M-Link
Dimensions110 x 72 x 24 mm
Weight115g
Weight Sensor Switch15g
Temperature range-30°C to +75°C

Overview

The PowerBox Cockpit SRS is identical in design and construction to the PowerBox Competition SRS, with the addition of one special feature: a freely programmable door sequencer for warbirds or jets.

SRS stands for Serial Receiver System: in contrast to conventional battery backer systems, servo information is transferred using a digital serial signal generated by the receiver. This reduces the number of connections required between the receiver and the PowerBox to a single cable. It is also a straightforward matter to connect a second receiver to the system, which then assumes complete control of the model without restriction if the first receiver should fail to pick up a signal. In the case of Spektrum and Jeti equipment additional receivers are not required; only the satellite receivers are connected to the Cockpit SRS.

The integral door sequencer is an in-house development by PowerBox Systems, and opens up entirely new territory in terms of programming facilities. The operation of the wheel doors is freely programmable, i.e. it is not restricted to pre-set sequences. In spite of the innumerable possible options which the door sequencer offers, all the set-up work can be completed in just a few minutes thanks to the software-based set-up assistant, which has been an integral feature of the sequencer since 2012.

The Cockpit SRS can output up to twelve channels, regardless of the radio control system with which it is used. Four of them are equipped with a servo-match function.

The purpose of servo-matching is to adjust the centre point, end-points and direction of rotation very accurately for each servo. This means that multiple servos connected mechanically to a single control surface can be fine-tuned to operate exactly in parallel, preventing the servos working against each other. They are able to develop their full power, and consume less current. Servo-matching can also extend the effective life of your servos enormously.

However, servo-matching also allows functions to be linked, avoiding the need for two channels at the transmitter. As an example: the left and right landing flaps can be operated using just one transmitter channel, as the direction of rotation and the servo end-points are adjusted at the Cockpit SRS. This saves channels, and in many cases makes the transmitter programming procedure much easier.

All the settings are programmed using the SensorSwitch in conjunction with the high-resolution OLED screen. All the menu points are displayed in full text form on the screen - rather than as abbreviations - which makes it much easier to understand the procedure.

The Cockpit SRS offers the option of a telemetry link with various radio control systems. This facility enables the pilot to view the voltage and residual capacity of both batteries on the transmitter's integral screen. The telemetry interface is simply connected to the receiver using a patch-lead; the TM1000 telemetry module is only required with Spektrum equipment. The receiver then sends the data directly to the transmitter screen. Alarms - such as battery failure - are also generated at the transmitter itself.

The high-resolution OLED screen displays the voltage and residual capacity of both batteries, as well as the output voltage actually present.

The Cockpit SRS delivers a regulated output voltage of 5.9 V or 7.4 V, making it a great choice for standard 6.0 V servos as well as HV systems. In both cases the constant output voltage ensures consistent running and extended effective life for your servos.

The PowerBox Cockpit SRS can be updated using the USB interface adapter. This means that future expansions - such as additional telemetry systems - can be loaded and used in just a few minutes.

Richo from Desert Aircraft Australia takes a look at a couple of the new systems from Powerbox and demonstrates the door sequencing capability.

Related Products

Bluecom Adapter

Bluecom™ Adapter

PB9021

View Product

Teleconverter S-BUS 2

Teleconverter S-BUS 2

PB5600

View Product

Battery 2800

Battery 2800

PB2810

View Product

Battery 3200 (Li-Fe)

Battery 3200 (Li-Fe)

PB3210

View Product

Battery 4000

Battery 4000

PB4010

View Product

MagSensor

MagSensor

PB9040

View Product

USB Interface Adapter

USB Interface Adapter

PB9020

View Product

PowerBox logo

Order Code: PB4620
Manufactured By
PowerBox-Systems